Solar control · EN 1096

Low-E and solar control
coated glass

China Glass Factory applies single, double and triple silver Low-E coatings to float and low-iron glass in Qinzhou, China, in insulating units up to 3,300 × 8,000 mm and U-value 1.1 to 1.8 W/m²K. Specification is set by U-value and solar factor, not by trade name. Production runs 7–15 days after order confirmation.

Silver layers1–3
U-valuefrom 1.1 W/m²K
Light transmissionup to 70 %
TemperableYes
Low-E coated glass for solar control on east and west facades Single to triple silver

Specification

What coatings, U-values and sizes can you produce?

These are the limits of our own lines, not a catalogue range. If your drawing sits outside one of them, tell us and we will say so before you spend time on a tender.

Coating typeOff-line soft coat (sputtered), on-line hard coat (pyrolytic)
Silver layersSingle, double and triple silver
SubstrateClear float, low-iron, tinted, or body-tinted
TemperableYes for temperable grades; hard coat can be tempered after coating
U-value1.1 to 1.8 W/m²K in a double-glazed unit
Solar factor (g)0.25 to 0.45 depending on coating
Light transmission40 to 70 % depending on coating and glass thickness
Maximum size3,300 × 8,000 mm as an IGU
StandardsEN 1096-1/2, EN 410, EN 673
Edge deletionStandard 10 mm for IGU, wider on request

Applications

Where is Low-E glass used?

Same product, different build-up. Send the application and the design load, and we will propose the configuration rather than quote the nearest standard panel.

01Hot climates

Middle East, Southeast Asia and Africa — double silver cuts solar gain without turning the façade black.

02Cold climates

Europe and northern China — keeps heat inside while letting daylight through.

03Retrofit glazing

Hard-coat Low-E can replace existing single glazing in the same frame on some refurbishments.

04Skylights

Combined with laminated inner pane for overhead solar control.

Export packing for architectural glass — end-cap and steel frame crates for container shipment to Manila and Cebu

Packing

How is the coated face protected in transit?

Soft-coat Low-E scratches easily and cannot be cleaned with abrasives, so coated panes are packed with the coating face wrapped and every panel interleaved. On site the protective film comes off only at installation.

  • Coating face wrapped and marked
  • Foam interleaving between coated panels
  • Edge deletion area kept free of film
  • Crate marked COATED SIDE — do not stack flat
  • Handling gloves supplied with the first crate

Approvals

What standards and test reports come with it?

Certificates are issued in the manufacturer's name, and the test reports travel with the shipping documents so your consultant can review them before the glass arrives.

CE — EN 1096 CE — EN 1279 (as IGU) ISO 9001:2015 China CCC

Questions

What do buyers ask first?

Can soft-coat Low-E be used as a single pane?
No. Off-line soft coat has no protection against handling and moisture, so it must face into a sealed cavity. For monolithic use you need on-line hard coat, which is durable but has a higher U-value.
Does Low-E glass look dark from outside?
It changes the appearance, and how much depends on the coating. A neutral double silver looks close to clear; a triple silver with a low solar factor reads noticeably darker and bluer. We send sample photos against your reference glass before production.
Which surface should the coating be on?
In a standard double-glazed unit in a hot climate, surface 2 — the inside face of the outer pane. In a cold climate it can be surface 3 instead, to keep the inner pane warmer. Tell us the climate and we specify the surface on the drawing.
Does the coating survive tempering?
Temperable grades do. They are designed for it, but the coating is applied before tempering and the process is controlled so the optical properties stay inside tolerance. Hard-coat glass can also be tempered after coating.

Low-E glass price Philippines: Price from USD ___ per sqm FOB Qinzhou. The coating stack, the substrate and the IGU build-up each carry their own premium, so a glazing schedule is quoted line by line.

What do we need to price your drawing?

Tell us the build-up, the quantity and the destination port. You will get a specification review and an indicative price within one working day — reviewed by an engineer, not a bot.

ContactWang Zhi · Export Sales

We reply within one working day. Drawings in DWG, PDF or Excel are welcome.

How is Low-E glass shipped to the Philippines?

Low-E coated glass is supplied to Philippine projects from our own plant in Qinzhou, China. Test reports for heat-strengthened and fully tempered flat glass are provided on request. The PS licence itself is held by the local manufacturer and the ICC is applied for by the importer. Shipments are quoted FOB Qinzhou or CIF Manila, Cebu or Davao, minimum one 20ft container, production 7-15 days after order confirmation. Port, duty and documentation details are on the Philippines market page; Manila and Cebu have their own pages.

Last updated: 2026-11-21. China Glass Factory, Qinzhou, China. Prices are indicative FOB Qinzhou and confirmed against your drawing.