Curtain wall glass and facade glazing

China Glass Factory makes vision, spandrel, laminated and fire-rated glass for unitised, stick-built and point-fixed facades in its own plant in Qinzhou, China — jumbo lites up to 3,660 × 12,000 mm, heat-soak tested in-house, 7–15 days after order confirmation. Verified 7 November 2026.

What glass does a curtain wall actually need?

A curtain wall takes three glass families in one system: Low-E insulating units for the vision areas, ceramic-fritted glass for the spandrel bands so the facade reads as a single plane, and laminated glass with PVB or SGP wherever the elevation faces windborne debris. Sizing is driven by the design wind pressure for each opening, not by a general thickness table, and heat-soak testing is normally specified for high-level or overhead glazing because it moves spontaneous breakage risk from the building to the factory floor. China Glass Factory produces all three in-house, with jumbo panels up to 3,660 × 12,000 mm (43.9 m² each) to cut joint count on tall elevations.

Which glass goes where on a facade?

ZoneProductTypical build-upWhat it is solving
Vision glassLow-E insulating unit6 Low-E tempered + 12A argon + 6 temperedSolar heat gain and U-value — the dominant cooling load in tropical projects
Spandrel glassCeramic-fritted6 fritted + 12A + 6, with opacifierHides the floor slab, matches the vision area so the facade reads as one plane
Debris-exposed elevationLaminated6 + 1.52 PVB + 6, SGP where structuralRetains the pane in the frame after impact — tempered alone cannot
Overhead, canopy, skylightLaminated + heat-soaked tempered8 + 1.52 SGP + 8 heat-soakedPost-breakage retention is a life-safety requirement overhead
Fire compartment junctionFire-ratedEI / EW / E as specifiedMaintains the rated separation where facade meets floor slab
Atrium and long spanJumbo or glass finUp to 3,660 × 12,000 mmFewer mullions, cleaner elevation, less steel

What does each facade system demand of the glass?

SystemHow glass is heldWhat matters for the glass
Unitised curtain wallPre-glazed into frames in the factoryTight dimensional tolerance and repeatability — the unit is built once and cannot be adjusted on site
Stick systemGlazed on site into mullions and transomsEdge work quality and the ability to handle large lites on site
Point-fixed / spiderBolted through drilled holesHoles are drilled before tempering and cannot be altered; SGP is normally specified for post-breakage load
Structural sealant glazingBonded to the frame with siliconeGlass is part of the load path — SGP, and strict control of coating and edge condition for adhesion
Cable-supported / glass finGlass carries loadSGP interlayer and heat-soaked tempered plies; deflection governs the design

Why do jumbo lites matter on a facade?

A 3,660 × 12,000 mm panel is 43.9 square metres. On a 30-storey elevation, moving from 2.4 m wide panels to 3.6 m wide panels removes roughly a third of the vertical joints. Each of those joints carried a mullion, a sealant line, a thermal bridge and a future maintenance point. The saving is not in the glass price — it is in the installation programme and in the number of places the facade can leak in year eight.

The constraint is the tempering furnace, which is why furnace size is the first question worth asking any supplier. A trader quotes a catalogue maximum; a plant quotes its own equipment limit, including the sizes it cannot take.

How do thermal and structural loads decide the build-up?

Thermal stress. Coated and fritted glass absorbs heat differently from clear glass, and edge condition matters — a chipped edge concentrates stress. This is why edge work specification is not cosmetic on a coated facade.

Deflection. Insulating units deflect under wind load and the gap between lites changes with temperature and altitude. Specifying the unit against the actual service condition, not the catalogue, avoids optical distortion and seal fatigue.

Inter-storey movement. A facade moves with the structure. Where the glass is part of the load path — glass fins, structural sealant, cable-net — the design must accommodate that movement, and the interlayer type becomes a structural decision rather than a cost decision.

Facade glass price Philippines: Price from USD ___ per sqm FOB Qinzhou. Jumbo size, Low-E coating, interlayer type and heat-soak each carry their own premium, so a facade package is quoted line by line against your schedule.

What do facade contractors ask most often?

What glass goes into a curtain wall?

Low-E insulating units for vision areas, ceramic-fritted glass for spandrel bands, laminated glass on debris-exposed elevations, and fire-rated glass at rated junctions.

Why use jumbo panels in a curtain wall?

Each joint removed also removes a mullion, a sealant line, a thermal bridge and a leak path. Jumbo lites up to 3,660 × 12,000 mm cut all four.

When is heat-soak testing required?

Normally for overhead, canopy, point-fixed and high-level facade glazing, where spontaneous breakage would be a safety event rather than a maintenance item.

How is the glass thickness decided?

From the design wind pressure for that opening and its support condition, derived by the facade engineer from the local wind code.

Can you supply spandrel matched to the vision glass?

Yes — fritted spandrel produced in-house, colour and thickness matched, with opacifier backing where the slab must not be visible.

How is facade glass shipped to the Philippines?

Facade glass is supplied to Philippine projects from our own plant. Test reports for heat-strengthened and fully tempered flat glass are provided on request. The PS licence itself is held by the local manufacturer and the ICC is applied for by the importer. Shipments are quoted FOB Qinzhou or CIF Manila, Cebu or Davao, minimum one 20ft container, with ACFTA Form E available for the preferential duty rate. See the Philippines market page, or the city pages for Metro Manila and Cebu.

Speciality glass Send a facade enquiry WhatsApp a facade enquiry Jumbo glass Insulating glass What we do differently

Build-ups shown are typical configurations and must be confirmed against the project's design wind pressure, thermal requirements and fire strategy by the facade engineer. Product scope and size limits are factory records verified 7 November 2026. Philippine desk: info@cnglassworks.com.

Last updated: 2026-11-21. China Glass Factory, Qinzhou, China. Prices are indicative FOB Qinzhou and confirmed against your drawing.