Glass Smoke Curtains for the Philippines
Tempered baffles from Qinzhou, China · 6–12 mm · 500–800 mm deep, cut to your drawing
China Glass Factory makes tempered glass smoke curtains in Qinzhou, China, for Philippine fit-outs: 6–12 mm clear or low-iron, cut 500–800 mm deep to your drawing, panels up to 2,440 × 3,660 mm, edges polished and fixing holes drilled. Production takes 7–15 days; sea freight to Manila adds 7–12 days. Minimum order is one 20 ft container, shareable with tempered panels.
Send the curtain depth per zone, thickness, bracket layout and destination port. We answer with a written FOB Qinzhou price within one working day, and we check your hole layout before cutting.
WhatsApp / phone: +86 138 3303 3053
Email: info@cnglassworks.com
Are smoke curtain, smoke baffle and draft curtain the same?
The consultant writes smoke curtain, the architect writes smoke baffle, the MEP drawings say draft curtain or smoke screen, and the Chinese factory file calls it a 挡烟垂壁. They all mean a vertical blade hanging below the soffit to hold the smoke layer in a reservoir above head height. The word on the drawing changes nothing on the order; four numbers do.
| What the drawing calls it | What it means physically | The number we need |
|---|---|---|
| Smoke curtain / smoke screen | Continuous blade from soffit down to the calculated reservoir depth | Depth per zone, in mm |
| Smoke baffle | Same blade, usually shorter and set between beams | Depth plus beam soffit level |
| Draft curtain | Blade under a sprinkler line, often only 300–500 mm | Depth and whether the sprinkler deflector stays clear |
| Smoke barrier (rarely glass) | A full smoke compartment wall, not a hanging blade | If the spec says barrier, check with the consultant — glass blades do not substitute |
One honest warning: glass is a fixed static curtain. If your design needs a curtain that drops on alarm, that is a motorised fabric unit from a fire-products supplier, not a glass panel.
What thickness, depth and price should you expect?
Price from USD 26 per sqm FOB Qinzhou for 8 mm tempered glass with polished edges and drilled fixings. The table is indicative; the written quotation follows your depth and bracket layout.
| Thickness | Indicative from (USD / sq m) | Where it is used |
|---|---|---|
| 6 mm (1/4 in), tempered | 22 | Short baffles to 500 mm, under sprinkler lines, low-ceiling retail |
| 8 mm (5/16 in), tempered | 26 | The common specification: 500–700 mm deep lobby and mall curtain |
| 10 mm (3/8 in), tempered | 31 | 700–800 mm deep, longer spans between brackets, atrium edges |
| 12 mm (1/2 in), tempered | 38 | Full 800 mm depth with wide bracket spacing, high-traffic atria |
| 8 mm tempered, heat-soaked | 29 | Any blade hanging over occupied space, where the spec calls for HS |
| 8+1.52 PVB+8 tempered laminated | 58 | Retained-pane specification; roughly double the weight per sq m |
Maximum panel 2,440 × 3,660 mm, so an 800 mm deep blade comes out of one 3,660 mm sheet with little waste. Low-iron base adds 10–15%. Prices exclude freight, 12% VAT and duty.
How long does shipping to Manila, Cebu and Davao take?
Smoke curtain blades are narrow and long, which packs well — but the polished bottom edge is what breaks. We crate vertically, interleave the faces and put foam on the arris.
| Port | Sea transit from Qinzhou | Notes |
|---|---|---|
| Manila (North and South Harbor) | 7–12 days | Most sailings; fits out Luzon atria without a transhipment |
| Cebu (Cebu Base Port) | 10–16 days | Fewer direct calls; a Manila transhipment adds 3–5 days |
| Davao (Sasa Wharf) | 12–18 days | Blades cube out before they weigh out — plan crate count, not tonnage |
Transit times are sailing schedules, not promises. Add 5–7 working days for clearance and haulage at the Philippine end.
Where does a glass smoke curtain earn its cost?
- Mall and airport atria. A clear 10 mm blade holds the smoke layer without cutting the sightline from the upper floor — the reason designers pick glass over a solid gypsum downstand. Pair it with fire-rated glass where the same line also has to be a fire separation.
- Office lobbies and escalator wells. A 600 mm blade over an escalator well is the usual Philippine detail; the partition line above often continues into it, so both are ordered together.
- Car park and basement ramps. Blades between beam soffits, 500 mm typical, usually 6 mm tempered because nothing hangs below them.
- Retail shells under a sprinkler grid. Short draft curtains that keep the deflector clear — the depth is set by the sprinkler layout, so send the reflected ceiling plan, not just the architectural one.
What will we not pretend about a smoke curtain?
- The smoke calculation is not ours. Depth, spacing and the reservoir volume come from your engineer's NFPA 92 analysis and the local fire code review. We cut what the drawing says. If the depth looks wrong we will say so, but we cannot sign the calculation.
- Certificates. The PS mark belongs to the local manufacturer and the ICC is issued to the importer per shipment. We supply factory test reports, tempering records and the heat-soak report where ordered — we do not sell you a licence number.
- No structural role. A glass blade is a smoke component, not a structural or fire-rated barrier unless the build-up is specified as one. Do not let a value-engineered drawing turn it into a fire separation.
- Bracket supply. Channels, spiders and anchors are local fabrication. We drill to your layout and check it, but the fixing into the soffit is your structural engineer's call.
Questions Philippine buyers ask first
Can you cut different depths in one order?
Yes, and most projects need it. Zones rarely share one depth; we cut per zone and stencil the zone code on each crate so the installer does not have to measure at height. Tell us the zones in a simple list, depth in mm per zone.
What tolerance do you hold on depth and holes?
Depth plus or minus 1 mm, hole position plus or minus 1 mm, with hole edge at least two glass thicknesses from the pane edge. Send the bracket layout as a dimensioned sketch or DXF; a photograph of a bracket is not enough to drill from.
Why does the bottom edge cost extra?
Because it is flat polished and arrised, hand work rather than a straight cut. It is the difference between a blade at head height that is safe to brush past and one that is not. It adds roughly USD 4–6 per linear metre, and we do not quote a smoke curtain without it.
Depth per zone, thickness, bracket layout and destination port are enough to start. You get a layout check and a written price within one working day.
What other glass do we ship to the Philippines?
- Tempered glass — the base pane for every smoke curtain blade
- Fire-rated glass — where the same line must also hold fire, not just smoke
- Laminated safety glass — retained-pane build-ups for overhead work
- Jumbo glass — longer blades with fewer joints in a big atrium
Request a smoke curtain quotation — send the depth per zone, thickness, bracket layout and destination port.
Lead times on this page were checked against factory records in November 2026. Prices are issued only against a drawing or glass schedule, in writing, and are valid for 30 days from issue.
Last updated: 2026-11-22